Language Select
  


FONDU / FONDURIT / SOLID FLOOR : PRIMEBASE / FLASHFLOOR / POLYTHANE
PERMASHINE / LiQUID HARDENER / WATERPROOFING

 


• Fondu / Fondurit

o How  maximum/minimum thickness is FONDU and FONDURIT?

- The minimum thickness for FONDU is 5 cm. The maximum thickness is up to the customer.
- FONDURIT is about 6 mm thick. It can be used as a color finish for FONDU or as a protective layer in a cold room.

 

o At what temperature does the room need to be during installation?

- Should be higher than 5 degrees Celsius. However, it can also be installed at lower temperatures with a catalyst.


o Can you buy material and install it by yourself?

- สามารถซื้อวัสดุไปทำเองที่หน้างานได้ โดยทางบริษัทฯ จะมีเจ้าหน้าที่ไปแนะนำวิธีการติดตั้งให้ที่หน้างาน
- Yes, that is possible. One of our Technical staff will recommend you at the work site.


o How long is the curing period?

- FONDU takes 6 hours
- FONDURIT takes 12 hours for foot traffic
   24 hours for light traffic
   48 hours for forklifts


o How much weight can Fondurit hold?

- Fondurit can hold more than 5 tons at 6 mm.


o Can Fondurit be used for spot repair ?

- FONDURIT can be used for spot repair  by cutting in square , preparing the surface, and coating with  FONDURIT.


o How about FONDU joints?

- Joints should be cut every 5x5 m as soon as concrete hardens.

 

o Joint generally causes the Folk lift impact. As a result, for floor crack, is there a solution?

- Have to cut in a good shape.

 

o What is the difference between Freezing Concrete and FONDU

- Freezing Concrete is a normal ordinary Portland concrete adding Foaming Agent. Can be used in Cold room. It is also a high strength concrete that can resist in sub zero area and thermal shock but have to coat with Polyurethane. Freezing concrete can completely cure in 21-28 day

FONDU is an 40% alumina cement, can resist temperature from sub zero temperature up to 500 degree Celcius. FONDU can withstand temperature in Freezing room -40 degree Celcius especially in front of Cold room where thermal shock is required. It is a rapid setting cement that can be completely cure in 6 hours. FONDU can also be used in metal industries.


o What is the pH tolerance of the floor?

- FONDU allows pH 3.5 – 12
- FONDURIT allows pH 4.5-7

 

o Can FONDURIT be used as a wall finish?

- No. But we recommend using FONDUR Premix for wall finish.

 

o What colors are available for FONDURIT?

- Green, red, yellow, light grey and natural concrete color.


o Do you have a certificate for FONDU / FONDURIT?

- We have a certificate  FDA ( Foods and Drugs) for FONDU and FONDURIT


o Do you have a warranty policy?

- We offer a warranty period of 1 year.


o Will there be any cement dust  after FONDU installation?

 - No

 

o What is the difference between FONDU and FONDU Premix

- FONDU is an alumina cement that has to be mixed with additional elements, like gravel, sand, admixtures, foaming liquids. On the other hand, FONDUR Premix does not need any additional mix. It is already composed with sand. Before using, only water is needed.


o How do you prepare the floor base before installation?

- For FONDU, chipping the existing floor, place the foam, and lay out the wiremesh. After, pour FONDU until you reach your required floor thickness.
- For FONDURIT, prepare the floor with a scarifying machine. Clean with high pressure water jet and after coating with FONDURIT.



• SOLID FLOOR : PRIMEBASE / FLASHFLOOR

o What makes SOLID FLOOR : PRIMEBASE different than other concrete floors?

- Most concrete floors require 5 cm toppings for higher strengths (240 ksc) and takes about 21 days to cure. PRIMEBASE reaches a strength of 400 ksc in only 3 days. It also doesn’t leave any cement dust.

 

o Will PRIMEBASE peel off from the existing concrete?

- No, PRIMEBASE has a strong bond to the concrete and will not peel off. Before applying PRIMEBASE, we have to scarify the existing floor horizontally and diagonally to about 3 mm deep. This will increase the grip of the concrete. Afterwards, we clean the floor with a high pressure water spray and then we can pour the PRIMEBASE topping.


o How strong is PRIMEBASE compared to other concrete floors?

- PRIMEBASE has a higher bonding and density than most concrete floors because it’s a polymer mortar. It is composed of cement, quartz sand and resin.


o How do you maintain the thickness of PRIMEBASE?

  • - You can control it by the volume or using the rake.


o How about the flatness of PRIMEBASE?

- As PRIMEBASE’s thickness is between 6 mm to 2 cm, the floor can be adjusted less than 5 mm every 3 m.


o What kind of texture does PRIMEBASE have?

    - PRIMEBASE’s surface is similar to that of trowelling concrete. The color is a little darker. After installation, there might be some white stains, which will fade after a month to three months of cleaning / mopping.


o Will the color of the finish floor be different than the existing concrete floor?

    - The finish floor will be slightly darker than the existing floor.


o If repair in spot area, it will be peel off?

    - No, because we will also scarifying a surface 3 mm. depth , cleaning before surface coating.

 

o How are the joints cut after installing PRIMEBASE?

- That depends on the concrete floor and the existing structure. PRIMEBASE usually follow the same joint layout.  


o Can PRIMEBASE repair cracks caused by existing structure?

- No. The structure must be fixed first, then PRIMEBASE can be applied.


o Will there be any cement dust after installation?

    - No, the floor will be dustproof.

 

o Will there be any dust during installation?

- A little. By using a wet scrifyinging technique, we will be able to limit  dust particles.


o Is PRIMEBASE slippery?

- No.

 

o Is it resistant to acid and chemical products?

- We recommend using PRIMEBASE CSR for higher tolerance.


o Can PRIMEBASE / FLASHFLOOR be installed in cold / freezing rooms?

- Yes. But the temperature must be constant.


o How much weight can PRIMEBASE hold?

- 6 Tons


o How long is the curing period?

- About 3 days.


o How is the claening process?

- Simply by mopping or by using a high pressure water jet.

 

o Can it be installed outdoors?

- Yes, it is possible. We will confirm again after looking at the job site.


o What is the maximum thickness of PRIMEBASE?

- 5 cm


o About how much can be installed in a day?

- 300-350 M2 at 6 mm deep.

 

o How would you prepare the floor before installation?

- By scarifying the floor horizontally and diagonally.

 

o Is it possible to use other finishing products on top of PRIMEBASE?

- Yes.

 

o What is the advantage of PRIMEBASE?

- PRIMEBASE can be installed over concrete that has gone through humidity. The curing process is relatively faster than other floor finish. It only takes about 3 days to cure and reaches a strength of 400 ksc. However, there might be some white stains on the surface which fades away eventually after weekly cleaning (for about 3 months).


o What is PRIMEBASE / FLASHFLOOD recommended for?

 - It is recommended for fixing old warehouse floors that has gone through some peeling of the surface, for adjusting floor levels, and for industries that need a quick-strong-fix floor

 

o What colors are available for FLASHFLOOR ?

- Gray, yellow, green, and red.

 

o Will the color fade?

- Not if it’s used inside. If it’s used outside, the color will wear out over time


o If the existing floor is Floor Hard, can FLASHFLOOR be used to fix the floor?

- Yes, it can.

 

o Is it resistant to scratch?

- It is much more resistant to scratches than Resin products.


o Can be installed PRIMEBASE/ FLASHFLOOR in damp area?

- Yes, it can.


o What is your warranty policy?

- We offer a warranty period of 1 year.


o What strength should the concrete be before installation?

- At least 210 ksc(Cyl)


 



• POLYTHANE

o At what temperature does the room need to be during installation?

- Higher than 10 degrees Celsiius and not fall down to 5 degrees Celsiius within 24 hour


o How many kinds of POLYTHANE do you have?

- We have GF 2mm, MF 3,4 mm, HF 6,9 mm, C&G for cove and gutter

 

o What colors are available?

- We have grey, beige, yellow, green, and red for standard color. Other colors are also available, please refer to this chart (www.ralcolor.com)

 

o How is the minimum and maximum thickness of POLYTHANE?

- Minimum thickness is 1.5 mm.

 

o What is POLYTHANE recommended for?

- Food industry

 

o Can it be installed in humid conditions?

- It must be less than 5% humidity.

 

o How much weight can it hold?

- GF and MF can hold up to 3-4 tons. HF at 6 to 9 mm can hold up as much as 6 tons.

 

o Do you have a warranty policy?

- We offer a warranty period of 1 year for Polythane.


o How thick does Polythane need to be in a cold / freezing room?

- In a freezing room, at 9 mm and in a cold room, at 6 mm.


o Can it be installed outdoors?

- Not recommended because the color will wear out quicker.

 

o Is it resistant to scratch ?

- Polythane HF is more resistant to scratches than Polythane MF


o What is the difference between Polythane and Rocapox (epoxy)?

- Polythane เหมาะสำหรับงานไลน์เปียกและห้องเย็น คุณภาพสูงกว่าในเรื่องการยืดหยุ่นตัว, การเซ็ตตัวเร็วกว่า, การทนอุณหภูมิ, ทนความชื้น
- Rocapox(Epoxy) เหมาะกับงานไลน์แห้งที่เป็นโรงงานที่น้ำมันเครื่องมากๆ มีความแข็งแต่เปราะ
- Polythane is suitable for wet and cold process. Higher quality in terms of flexibility, setting time, temperature resistant and moisture resistant.
- Rocapox (Epoxy) is suitable for dry factory or machinery processing line. It is hard but brittle.


o What is the lifespan of Polythane?

- About 5 years.

 

o Can Polythane be used to adjust the floor level?

- It’s not recommended when it’s too deep.


o What strength should the concrete be before installation?

- 210 ksc
- 210 ksc


o How do you prepare the floor base before installation?

- Prepare with a scarifying machine or shotblast.

 

o What if the color fades?

- We recommend using Coating Polythane CT



• PERMASHINE / LIQUID HARDENER

o What is your warranty policy for PERMASHINE?

- We offer a warranty period of  dust proof 5 years for PERMASHINE.

 

o What strength should the concrete be before installation?

- At least 210 ksc(Cyl)


o How would you prepare the floor before installation?

- Clean the existing floor. It should be most free from dust and particles. If there is any coating, peel off the coating. If there are cracks, first fix the cracks. 


o What colors are available?

- Please ask for sales brochure


o Will the color peel off ?  

- No


o Is it resistane to scratch?

- Yes, it is!


o Can it be used to repair cracks?

- We recommended using 10 Minute Concrete Mender to repair cracking.


o Can it be used to adjust floor levels?

- It may be possible, although it is not recommended.


o Can be used PERMASHINE for area not good leveling?

-  Yes, but we will see sand and stone exposed.


o Is it resistant to acid and chemical products?

- Yes it can, although a quick clean right after is highly recommended.


 o Is it slippery?

- No


o Where else is this PERMASHINE specialty?

- PERMASHINE liquid hardener is imported from the US. It has certificates from Green spec and NFSI. It is non-slippery, odorless, and resistant to scratches.


o Can oil penetrate through PERMASHINE?

- Yes. We recommended coating  with oil repellent ROCAROL.


o About how much can be installed in a day?

- About 150 – 200 M2/day/ 1 team


o What is the price difference between  sand exposed and stone exposed?

- The price is not the same.


o After installation, some cracks appear. Can that be fixed?

- Yes. With PRIMEBASE, or Concrete Mender. Fill in the cracks and polish with PERMASHINE.



• WATERPROOFING


o What type of Waterproofing is available?

- 1. Rocathane 2. Rocaflex 4 3. Rocasyl 4. Rocacryz 5. Ceracoat


o How is it installed?

- By rolling, plastering or spraying.


o Where can it be used?

- Roofs, watertanks, walls, and balconies.


o Have to used Fiber Net?

- Yes, in Rocasyl. In area between floor and wall and crack area.


o Can it also protect sea water?

- No.


o Can it be used on walls?

- Yes.

 

o Can it be used for water tank?

- Yes


o Do you have a warranty policy?

- We offer a warranty period of 3 – 5 years.


o Are there colors available?

- Yes



COPYRIGHT@2013 ALL RIGHT RESERVED DESIGN BY ROCA10.COM